Octagonal Wooden Mirror By Daniel Rozin

Daniel Rozin’s Mirrors

By: Caitlin Arnold, Reporter
“The mirror is doing more than taking your image, it is capturing something about your soul and showing it back to you. These amazing works of art wouldn’t be possible without the engineer and you."- Daniel Rozin
Read Story
Arduino Uno R3 Elegoo Controlling A Servo Motor With A Joystick Project

Arduino Uno R3 Elegoo Controlling A Servo Motor With A Joystick Project

By: Nazli Pazhouhfam, Reporter
The materials you will need for this project are 3 breadboard jumper wires, 3 female-to-male dupont wires, a joystick, a servo motor, a uno R3 controller board, and a USB cable.
Read Story
plouc68000,November 18,2018, Arduino project hub

Elegoo Arduino Uno R3 Clock

By: David Katsanis, Reporter
After doing a lot of research I found the simplest Elegoo Arduino Uno R3 clock.The design is simple and all you need is an Elegoo Arduino Uno, breadboard, two buttons and 16 m/m wires.
Read Story
Arduino Uno R3 Elegoo Controlling A DC Motor With A Joystick Project

Arduino Uno R3 Elegoo Controlling A DC Motor With A Joystick Project

By: Nazli Pazhouhfam, Reporter
Making the arduino uno r3 elegoo controlling a DC motor with a joystick project.
Read Story
Elegoo Arduino Uno R3 How To Build A Button That Turns On/Off A LED Light

Elegoo Arduino Uno R3 How To Build A Button That Turns On/Off A LED Light

By: Aiden Tran, Reporter
The following writing below are the directions and code for the LED button. Gotten from the Arduino software 1.8.13.
Read Story
How To Make A Led Turn On With A Button On Tinkercad And The Elegoo Uno R3

How To Make A Led Turn On With A Button On Tinkercad And The Elegoo Uno R3

By: Lucas Riedel, Journalist

Step 1: Is to go to Tinkercad and Start a new circuit Step 2: Is to get out you materials. So what your going to need is 1 Resistor A Arduino Uno 1 button 1 LED 1 Breadboard Small Step...

Continue Reading
Arduino Uno R3 Elegoo LED Sequential Control Project

Arduino Uno R3 Elegoo LED Sequential Control Project

By: Nazli Pazhouhfam, Reporter

Today I will be making the arduino uno R3 elegoo LED sequential control project. The materials that you will need for this project are, one uno R3 controller board, one 830 tie-points breadboard, one USB...

Continue Reading
Arduino Uno R3 Elegoo Servo Project

Arduino Uno R3 Elegoo Servo Project

By: Nazli Pazhouhfam, Reporter

Today I will be making the arduino uno R3 elegoo servo project. The materials you will need for this project are, a USB cable, the uno R3 controller board, 3 breadboard jumper wires, and one servo motor...

Continue Reading
Elegoo  Arduino R3 How to Make multiple LED lights blink.

Elegoo Arduino R3 How to Make multiple LED lights blink.

By: Trevor Nothdurft, Reporter

This is how you can make multiple LED lights blink at once. What you need 1 Arduino R3 board., 4 LED's, 4 resistors, 1 Bread board, 9 wires, 1 USB cable and the Arduino app. 1st.plug a wire into...

Continue Reading

Elegoo Arduino Uno R3 – “Tone Keyboard” Project

By: Valerie Lai, Reporter
How to make a tone keyboard using the Elegoo Uno R3 Starter Kit.
Read Story

Elegoo Adruino Uno R3 – Ground Proximity Sensing with Ultrasonic Sensor Project

By: Khira Reavis, Reporter
This Elegoo Arduino is a miniature counterpart of radio altimeter, that is used on commercial aircrafts,
Read Story
Elegoo Arduino Uno R3 How to Make LED Lights Flash Morse Code

Elegoo Arduino Uno R3 How to Make LED Lights Flash Morse Code

By: Trevor Nothdurft, Reporter
Ever want to make a led light up into Morse code? Then this for you this has what you need and how to do it.
Read Story
Load More Stories
Activate Search
Real Stories, Real People, Real Life
#Arduino